2.5" SSD RB31 (Power Plus)

2.5" SSD RB31 (Power Plus)

2.5" SSD RB31 (Power Plus)

2.5" SSD RB31 (Power Plus)

Industrial SATA III 2.5" SSD
Power Plus for data protection
StrongMLC mode, up to 256GB capacity
Commercial/extended/wide temp. solutions
Built-in ECC and OCP/OVP
NCQ/TRIM/SMART support
mSMART storage device monitoring

Request a Quote

2.5" SSD RB31 (Power Plus) is SATA III 6Gb/s StrongMLC solid state drive with Power Plus technology. MemxPro Power Plus with firmware control and POSCAP design prevents data loss from unexpected power failure events. The 2.5" SSD RB31 is ideal for applications requiring higher levels of endurance for in-vehicle, transportation, and mission-critical demands.

Interface	SATA III
Form Factor	2.5" SSD (SFF-8201)
Flash Type	StrongMLC
Max. Channel	4
Density	32GB~256GB
Sequential R/W (MB/sec, max.)	552/439
Operating Temperature	0°C~+70°C/-25°C~+85°C/-40°C~+85°C
Max. Power Consumption	6W (5Vx1.2A)
Dimension (LxWxH/mm)	100x69.85x9.3
Operating Voltage	5V±5%
Storage Temperature	-55°C~+95°C
External DRAM Buffer	V
Thermal Sensor	V
DEVSLP Mode	N/A
ATA Security	V
S.M.A.R.T.	V
TRIM	V
Vibration	20G (7~2KHz)
Shock Resistance	1500G@0.5ms
MTBF	>3 million hours

Type	Documentation	Size	Format
Datasheet	MEMXPRO_DataSheet_2.5_SSD_RB31(PP)_V2.0.pdf	446KB	PDF

Conformal Coating

According to customer’s requirement, MEMXPRO can apply a special protective coating on selected products against moisture, dusts, and chemical contaminants; preventing short circuits and corrosion.

Conformal Coating

According to customer’s requirement, MEMXPRO can apply a special protective coating on selected products against moisture, dusts, and chemical contaminants; preventing short circuits and corrosion.

Conformal Coating

According to customer’s requirement, MEMXPRO can apply a special protective coating on selected products against moisture, dusts, and chemical contaminants; preventing short circuits and corrosion.

OCP/OVP

Equipped with a built-in OCP (Over Current Protection) and OVP (Over Voltage Protection) IC, the SSD is able to shut down power to protect its data when encountering abnormal currents and voltages.

Power Plus

MEMXPRO Power Plus with firmware control and POSCAP capacitor design prevents data loss from an unexpected power failure. The power hold-up time with Power Plus is about 40~85ms, which is long enough for all data in the DRAM buffers to be totally written back to the NAND flash ensuring data integrity.

StrongMLC

MEMXPRO develops StrongMLC technology to highly enhance a 6x increase in MLC endurance with reduced capacity, offering SLC-equivalent performance at a relatively much lower cost than regular SLC.

TRIM

The TRIM command allows the OS to tell SSD which blocks of data are no longer in use and can be erased. This enhances write performance by releasing space.

Wear Leveling

Wear Leveling algorithms and bad block detection schemes are used to extend life span and efficient utilization of the NAND flash memory.

mSMART

mSMART is a MEMXPRO's utility which is designed to provide product details and S.M.A.R.T. information. Our customers are able to monitor health, temperature and the lifespan of each installed disk in the system.

Thermal Sensor

The sensor in a controller can measure temperature through a product to enhance its data integrity. With SMARTPro, customers can monitor the temperature of MEMXPRO's SSD inside their system.

ESD and EMI Protection

MEMXPRO’s products are designed to comply with Electrostatic Discharge (ESD) and Electromagnetic Interface( EMI) standards.